Security camera mounted on an exterior wall
News · Technology

Wi-Fi HaLow (802.11ah): What Long-Range, Low-Power Wi-Fi Means for Event and Temporary Sites

Wi-Fi HaLow trades speed for reach, which makes it useful for sensors and small cameras spread across a large site, but not for guest WiFi.

Quick answer

Wi-Fi HaLow is the Wi-Fi Alliance certification for IEEE 802.11ah, which runs below 1 GHz. In Australia it uses the shared 915 to 928 MHz band. It reaches about 1 km with rates from about 150 kbps to 86.7 Mbps, so it suits sensors, gate counters and low-rate cameras, while guests and live streams stay on standard Wi-Fi or wired links.

Published 12 November 2026 · EventWiFi, operated by SydneyITFix

What is Wi-Fi HaLow?

Wi-Fi HaLow is the Wi-Fi Alliance name and certification program for products built on IEEE 802.11ah. The Wi-Fi Alliance launched the certification in November 2021. It uses the same Wi-Fi family of protocols, but in sub-1 GHz spectrum rather than 2.4, 5 or 6 GHz.

The Wi-Fi Alliance technology overview lists these characteristics:

FeatureWi-Fi HaLow (802.11ah)
SpectrumSub-1 GHz, with country-specific bands
Channel widths1, 2, 4, 8 and 16 MHz
Data ratesAbout 150 kbps at the longest range, up to about 86.7 Mbps on a 16 MHz channel
RangeApproximately 1 km
Devices per access pointUp to 8,191 in the specification
SecurityWPA3 and Enhanced Open
Power savingTarget Wake Time and Restricted Access Window scheduling

Target Wake Time lets a battery device agree a schedule to wake, send and sleep. Restricted Access Window lets the access point give selected devices time to transmit, which reduces contention when many sensors share one channel.

Which frequencies does Wi-Fi HaLow use in Australia?

The Wi-Fi Alliance overview lists 915 to 928 MHz for Australia and New Zealand, compared with 902 to 928 MHz in the United States. It also advises device makers to confirm approved bands with the local regulator.

In Australia, short-range devices like these operate under the ACMA low interference potential devices (LIPD) class licence. The ACMA explains three points that matter for event planning:

  • There is no application and no fee for using class-licensed devices.
  • Devices must follow the conditions in the class licence and must not cause interference.
  • There is no protection from interference under a class licence.

The 915 to 928 MHz range is shared. The ACMA wireless microphone page says wireless microphones can use 915 to 928 MHz, and that a wide variety of devices, including Wi-Fi, use these ranges. The ACMA outcomes paper on remaking the LIPD class licence also discusses RFID transmitters in 920 to 926 MHz and says changes to 900 MHz RFID arrangements may be considered in a future update.

For planners this means two things. Buy equipment configured for the Australian band, and check what else is running nearby, such as RFID gates, wireless audio or telemetry, before relying on the link. Our article on wireless microphone spectrum rules covers the same sharing issue for audio.

Where could HaLow help on event and temporary sites?

HaLow fits jobs that send small amounts of data over distance, often from battery-powered devices, where running cable or adding access points is hard.

TaskHaLow fitUsually better
Gate counters and crowd sensors across a large fieldGoodNot needed
Temperature, power or water level monitoringGoodNot needed
Low-rate perimeter or car park cameraPossible, test firstWired or point-to-point link for high resolution
Card payment terminalsNot typicalDedicated 2.4/5 GHz network or 4G/5G with backup
Guest WiFi for phonesNo, phones do not use itStandard Wi-Fi access points
Live stream uplinkNoWired, 5 GHz or 60 GHz point-to-point link

Construction compounds, rural events and large outdoor festivals are the most likely places to see it, because the distance between a site office and a far gate can exceed what a standard access point covers. See our construction site internet page and temporary CCTV installation for how sensors and cameras connect back to the main network.

What are the limits of Wi-Fi HaLow?

  • Throughput is modest. Even the top rate on a 16 MHz channel is far below a modern 5 or 6 GHz access point, and long-range links run at the lowest rates.
  • The band is narrow and shared. With 13 MHz available in Australia, a few wide channels fill it quickly, and other class-licensed devices use the same range.
  • Range claims vary. Information Age reported in October 2025 on a 16 km field test in open rural conditions, with results drawn largely from one chipmaker's own testing. On a site with crowds, vehicles, metal structures and terrain, expect much less.
  • Phones and laptops do not support it. HaLow devices connect through a HaLow access point or bridge that links into the normal network.
  • The device range is still growing. Check certification and Australian band support before you plan around a specific device type.

For guest coverage, the normal planning numbers still apply: about 50 active devices per access point, roughly 900 square metres per access point in open areas, and about 1 device per person at public events. HaLow adds reach for sensors; it does not replace that design. Our access point guide explains the sizing.

  1. Use WPA3. The certification supports it, so do not run sensors on an open or legacy network.
  2. Keep it separate. Put HaLow bridges and sensors on their own network segment, away from payments and guest WiFi. See separate networks for events.
  3. Change default credentials and update firmware. The ACSC tips for internet of things devices recommend both, along with turning off features you do not use.
  4. Check the smart device rules. The Department of Home Affairs security standards for smart devices set minimum requirements for many consumer connected products.
  5. Record what is installed. Keep a list of every sensor, its location and channel, so it can be removed or checked after the event.

Should you plan for HaLow at your next event?

For most indoor events and compact venues, no. Standard Wi-Fi access points and a wired backbone cover the space well. HaLow becomes worth considering when the site is spread out, devices are battery-powered, and each one only needs to send a little data, for example counters at several entry gates or monitoring at a remote generator or water point.

Start with a site survey and coverage plan, which shows where standard access points reach and where a long-range link would help. You can also send the site plan and a list of devices, and we will suggest how sensors, cameras, payments and guest WiFi should be connected.

Questions people ask

Is Wi-Fi HaLow the same as normal WiFi?

It is part of the same Wi-Fi family and is certified by the Wi-Fi Alliance, but it runs below 1 GHz under IEEE 802.11ah. Phones and laptops do not connect to it directly.

What frequency does Wi-Fi HaLow use in Australia?

The Wi-Fi Alliance lists 915 to 928 MHz for Australia and New Zealand. Devices there operate under the ACMA class licence, which has no fee but gives no protection from interference.

How far does Wi-Fi HaLow reach?

The Wi-Fi Alliance cites approximately 1 km. Longer distances have been reported in open rural field tests, but crowds, metal structures and terrain reduce range on real event sites.

Can Wi-Fi HaLow carry a live stream?

It is not a good choice. A live stream needs 10 to 20 Mbps of stable upload with headroom, so use a wired, 5 GHz or point-to-point link instead.

Can HaLow replace guest WiFi at a festival?

No. Guest phones use 2.4, 5 or 6 GHz Wi-Fi. HaLow is best for sensors and low-rate devices spread across a large site.

Sources

  1. Wi-Fi Alliance: Wi-Fi CERTIFIED HaLow delivers long range, low power Wi-Fi (2 November 2021)
  2. Wi-Fi Alliance: Wi-Fi CERTIFIED HaLow Technology Overview (November 2021)
  3. Wi-Fi Alliance: Wi-Fi HaLow overview page
  4. ACMA: Low interference potential devices (LIPD) class licence
  5. ACMA: Wireless microphones (shared 915 to 928 MHz range)
  6. ACMA: Outcomes paper, remaking the LIPD class licence (September 2025)
  7. Information Age (ACS): How to connect to Wi-Fi from 16km away (14 October 2025)
  8. Australian Cyber Security Centre: Tips to secure your internet of things device
  9. Department of Home Affairs: Security standards for smart devices

Event dates, prices and product details can change. Check the organiser or manufacturer before you plan around them. Planning figures are starting points; every network is confirmed against the actual site.

Planning a network for an event or site?

Our Sydney-based team can survey, connect, install and support it. Send the details and we will come back with a plan.